Printer Repair Marietta, GA

Problem: Lexmark MX510de in Austell, GA producing black pages intermittently.

Solution: Technician inspected the imaging unit and found no defects; discovered spilled toner pooled beneath the imaging unit. Vacuumed out accumulated toner. Output returned to normal with no additional issues noted.

Problem: Kyocera FS-9530dn laser printer in Douglasville, GA required installation, but the unit received was missing the face-up exit assembly.

Solution: Technician installed the Kyocera FS-9530dn, identified the missing face-up exit assembly, uninstalled the unit, and rebooted after confirming the incorrect model had been sourced. Installation was deferred pending receipt of the correct printer configuration.

Problem: Kyocera FS-9530dn laser printer in Douglasville reported persistent paper jams and failure to recognize Tray 2.

Solution: Diagnosed faulty Tray 2 assembly as the source of feed errors and tray recognition failure. Replacement Tray 2 was ordered and shipped directly to the customer's location.

Problem: Brother MFC-L8900CDW color laser multifunction printer leaving a repeating indent on printed pages.

Solution: Diagnosed indentation pattern as a fuser defect on the Brother MFC-L8900CDW. Replaced the fuser unit and tested the device to confirm clean, artifact-free output.

Problem: Lexmark CX310n presented with multiple issues including grinding noises and a cyan color output failure with no corresponding error messages displayed.

Solution: Technician removed the imaging unit, inspected the laser lens, and found the main drive coupler had dislodged. Replaced the EP drive assembly, verified scanner calibration, and confirmed print quality restoration and elimination of grinding noise.

Problem: Zebra GX430t thermal label printer in Alpharetta, GA was due for scheduled preventive maintenance (unit 7 of 7).

Solution: Performed full preventive maintenance on Zebra GX430t at 122,014 inches of media feed. Cleaned internal components and verified printer configuration.

Problem: Kyocera Ecosys FS-9530dn presenting with toner smearing, faded image in spots, and ghosting on output. Device was printing approximately 80,000–100,000 pages per month with prior maintenance and drum kit replacements over a year earlier.

Solution: Installed a 9-part OEM maintenance kit including fuser and drum components. New developer unit initially caused blank pages; 120–150 conditioning pages were run to allow toner to mix with developer powder before normal output resumed. Developer unit replacement also cleared the perform-maintenance m

Problem: Kyocera FS-2100dn laser printer in Smyrna experiencing chronic paper jams, lead-edge tearing on every second page, and ghosting output.

Solution: Technician diagnosed worn tray 2 roller assemblies (part 302F909171), a faulty fuser (part 302LV93130), a likely clutch or registration sensor flag issue causing lead-edge tears, and an overdue drum unit. Customer elected to replace the printer rather than repair.

Problem: Lexmark T654n laser printer producing a dark vertical line down the right side of every printed page.

Solution: Diagnosed the streak as a depleted toner cartridge depositing excess toner along the right margin. Replaced the cartridge, cleaned the printer, and tested output to confirm the defect was eliminated.

Problem: A label had wrapped around an internal roller on a Kyocera Ecosys M2540dw, causing degraded print image quality.

Solution: Technician removed the wrapped label from the developer unit. Persistent image defects prompted replacement of the developer and drum units via an imaging maintenance kit. The initial replacement kit produced output only on the left side of each page; reinstalling the original kit restored full-widt

Problem: Zebra ZT410 thermal printer producing barcodes with visible lines through the printed image.

Solution: Replaced the platen roller and printhead on the Zebra ZT410. Made multiple calibration adjustments to eliminate media wrinkles and restore consistent print quality.

Problem: Kyocera FS-9530dn laser printer reported crinkling paper output.

Solution: Replaced the stock fuser unit on the Kyocera FS-9530dn. Made adjustments to paper trays, then cleaned and tested the printer to confirm proper media handling.